Author Topic: Caille outboard motor wrench  (Read 4505 times)

0 Members and 1 Guest are viewing this topic.

Offline JoeCB

  • Contributor
  • Contributor
  • Hero Member
  • ***
  • Posts: 274
Caille outboard motor wrench
« on: September 01, 2017, 10:24:06 PM »
I thought that I would bump this old post from 2014. Still looking, other than a couple of hopeful responses from Bird, but nothing found to date, so here goes again. Now with a picture of the Caille motor.

Hello all, I have been looking for one of these for years. This wrench shows on the parts listings for the 1920 (ish) Caille Liberty Outboard motor. From the parts sheet illustration I'm guessing on the actual size being about 6 inch long. Also a guess that the big hex opening is 1 -1/8" , this based on the fact that that was a common size for the spark plug in use back then. Also a guess that this is a plain stamped wrench. The distinctive feature is the slot in the handle, again guessing that that was for use on the several wing nuts on this motor.
I'm looking to buy one... any chance that you have one kicking around? email at fixerjo@sbcglobal.net or PM me. Thanks for looking .

Joe B

Offline Papaw

  • Owner/Administrator
  • Administrator
  • Hero Member
  • *****
  • Posts: 11221
  • Alvin, Texas
    • Papawswrench
Re: Caille outboard motor wrench
« Reply #1 on: September 02, 2017, 11:04:26 AM »
That looks a lot like some of the Maytag wrenches, minus the slot.
Member of PHARTS - Perfect Handle Admiration, Restoration and Torturing Society
 
 Flickr page- https://www.flickr.com/photos/nhankamer/

Offline JoeCB

  • Contributor
  • Contributor
  • Hero Member
  • ***
  • Posts: 274
Re: Caille outboard motor wrench
« Reply #2 on: September 18, 2018, 12:10:09 PM »
Well, I'm still looking ! Must have been through a zillion boxes of flat wrenches at various garage and flea sales, but no luck as yet.  Keep an eye open for one for me , please.

Joe B

Offline international3414

  • Contributor
  • Hero Member
  • ***
  • Posts: 636
Re: Caille outboard motor wrench
« Reply #3 on: September 18, 2018, 01:27:08 PM »
i was going to say i have a few of them,but just seems to cruel :cheesy:....do you have the motor?

Offline JoeCB

  • Contributor
  • Contributor
  • Hero Member
  • ***
  • Posts: 274
Re: Caille outboard motor wrench
« Reply #4 on: September 20, 2018, 09:30:42 AM »
Yes the photo is of my 1920 Caille Liberty Drive single. It is a running motor, we run the old outboards at the Antique Outboard Motor Club meets. The caille's were made in Detroit by the Caille Perfection Motor Co. 

Joe B

Offline JoeCB

  • Contributor
  • Contributor
  • Hero Member
  • ***
  • Posts: 274
Re: Caille outboard motor wrench
« Reply #5 on: February 19, 2021, 10:06:48 PM »
Hello all, I thought that I would bump this back to the top for a fresh look. I'm still on the hunt for this Caille wrench.
Joe B

Offline skipskip

  • Contributor
  • Hero Member
  • *****
  • Posts: 1493
  • Glenmont NY USA
Re: Caille outboard motor wrench
« Reply #6 on: February 20, 2021, 08:39:50 PM »
Thanks for posting this.

I was finally motivated to go thru my buckets of  stamped wrenches.

Sadly I didn't find yours but I found some neat ones.

one for Mall chainsaw,  one for Indian motorcycle

and a couple of faux Ford ones

and I now have a box of yucky wrenches that can go away

Skip
A place for everything and everything on the floor

Offline JoeCB

  • Contributor
  • Contributor
  • Hero Member
  • ***
  • Posts: 274
Re: Caille outboard motor wrench
« Reply #7 on: February 24, 2021, 09:50:51 PM »
Skip, thanks for looking. I know that my wrench is sitting out there somewhere at the bottom of a dirty 5 gallon bucket.

Joe

Offline woodland_hank

  • Sr. Member
  • ****
  • Posts: 133
Re: Caille outboard motor wrench
« Reply #8 on: March 10, 2021, 01:23:21 PM »
Or the bottom of a lake...