Author Topic: Sutton Tool Company, Sturgis Michigan  (Read 735 times)

0 Members and 1 Guest are viewing this topic.

Offline lptools

  • Hero Member
  • *****
  • Posts: 1644
Sutton Tool Company, Sturgis Michigan
« on: April 06, 2018, 05:05:42 PM »
Hello, I have been trying to figure this one out, but I could use some help. The only thing that I am sure of is the the short shank is a #2 Jacobs Taper. The long taper looks like it would possibly be for a CNC Machine????????  The long taper is stamped A.M.T. 2 J.T. The coarse thread screw end looks to be left hand. I know that the Sutton Tool Company of Michigan closed its doors a while ago. Thanks, Lou
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society

Offline turnnut

  • Hero Member
  • *****
  • Posts: 1861
Re: Sutton Tool Company, Sturgis Michigan
« Reply #1 on: April 06, 2018, 06:02:58 PM »
 Lou, is that groove in the small end for a O-ring ?

 some of the work made by Sutton tool co: tools, jigs, special fixtures, chucks. they did high precision ID grinding also,
 plus many other items.

 the owner stopped working in 2005 and passed away in 2007 at age ? 97

 (googled)

Offline lptools

  • Hero Member
  • *****
  • Posts: 1644
Re: Sutton Tool Company, Sturgis Michigan
« Reply #2 on: April 06, 2018, 06:11:15 PM »
Hello, Frank.I don't think it is for an O-ring. It is a spiral groove, looks like a left hand twist to it, but now I am not sure . I will try a close-up. Thanks, Lou
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society

Offline turnnut

  • Hero Member
  • *****
  • Posts: 1861
Re: Sutton Tool Company, Sturgis Michigan
« Reply #3 on: April 06, 2018, 06:18:39 PM »
 yes, I see that now, Frank

 good shot.

Offline leg17

  • Hero Member
  • *****
  • Posts: 557
Re: Sutton Tool Company, Sturgis Michigan
« Reply #4 on: April 06, 2018, 07:43:05 PM »
Sure that's not right-handed?

Offline lptools

  • Hero Member
  • *****
  • Posts: 1644
Re: Sutton Tool Company, Sturgis Michigan
« Reply #5 on: April 07, 2018, 04:34:51 AM »
Hello, Leg17. It is a right hand thread, my mistake!!!!!! Thanks, Lou
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society

Online Plyerman

  • CONTRIBUTOR
  • Hero Member
  • *****
  • Posts: 1517
  • Northern Michigan
Re: Sutton Tool Company, Sturgis Michigan
« Reply #6 on: April 07, 2018, 05:58:53 AM »
It is a holder for a CNC machine alright, but I don't know which brand of machine. A drill chuck would go on the short Jacobs taper, as you rightly surmise. And then the long taper would go up into the spindle of the machine, held tightly in place by the large right-hand thread. But nowadays most all the machines use a retention knob on the end to hold the taper in the spindle. I've never seen one with a big external thread like that. Hmmm.
My friends call me Bob. My wife calls me a lot worse.

Offline lptools

  • Hero Member
  • *****
  • Posts: 1644
Re: Sutton Tool Company, Sturgis Michigan
« Reply #7 on: April 07, 2018, 08:31:22 AM »
Hello, Bob. Thanks for the info. There was some printing on the end label of the box, but unfortunately worn off!!!!! Regards, Lou
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society

Offline Spartan-C

  • Sr. Member
  • ****
  • Posts: 89
Re: Sutton Tool Company, Sturgis Michigan
« Reply #8 on: June 20, 2018, 02:27:09 PM »
You guys have it almost correct. 

That shank is for use in a Moore Jig Borer.  My guess, probably for a no. 1, or 2 machine.  I'm not totally familiar with them to give you precise details, but it is for a Moore jig borer or grinder.

Ken
Ken

Offline lptools

  • Hero Member
  • *****
  • Posts: 1644
Re: Sutton Tool Company, Sturgis Michigan
« Reply #9 on: June 20, 2018, 06:38:32 PM »
Hello, Ken. Thanks for the info!!!!! Regards, Lou
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society