Author Topic: Wrench Display Board  (Read 1665 times)

0 Members and 1 Guest are viewing this topic.

Online woodland_hank

  • Sr. Member
  • ****
  • Posts: 79
Re: Wrench Display Board
« Reply #30 on: May 10, 2018, 11:12:40 AM »
You wouldn't happen to have an extra 3/8 pebble combo would you?

What size large combos are you missing?

Mike

I need 13/16 and everything above 1".  Otherwise I have all of them including the 3/8" and 5/16".
« Last Edit: May 10, 2018, 11:19:04 AM by woodland_hank »

Online woodland_hank

  • Sr. Member
  • ****
  • Posts: 79
Re: Wrench Display Board
« Reply #31 on: May 10, 2018, 11:13:18 AM »
This will be the last display for a while (probably). I don't plan on any others till I finish my Plomb pebble combo set. Of course something in my workshop could catch my eye. The Stanley chisels were a spontaneous project. This is an Artisan/S-K ratchet and socket set I assembled. My grandfather had this set but my brother (retirement planner with little interest in tools) inherited them.

Offline mikeswrenches

  • Contributor
  • Hero Member
  • ***
  • Posts: 1737
Re: Wrench Display Board
« Reply #32 on: May 10, 2018, 11:59:00 AM »
Hank, I’m pretty sure I have a 1 1/16 in. one. It’s in my motor home so will be a few days before I can check.

Mike

Online woodland_hank

  • Sr. Member
  • ****
  • Posts: 79
Re: Wrench Display Board
« Reply #33 on: May 11, 2018, 06:59:24 AM »
Hank, I’m pretty sure I have a 1 1/16 in. one. It’s in my motor home so will be a few days before I can check.

Mike

Thanks!

Online leg17

  • Hero Member
  • *****
  • Posts: 523
Re: Wrench Display Board
« Reply #34 on: September 13, 2018, 06:05:17 PM »
Hank
Where did you get the clips holding the wrenches?

Online woodland_hank

  • Sr. Member
  • ****
  • Posts: 79
Re: Wrench Display Board
« Reply #35 on: September 21, 2018, 09:06:49 AM »
Which board are you talking about?  The open and combo wrenches are held on with simple L-hooks I bought at the hardware store.

Online leg17

  • Hero Member
  • *****
  • Posts: 523
Re: Wrench Display Board
« Reply #36 on: September 21, 2018, 04:19:20 PM »
that's the ones.
thanks

Offline d42jeep

  • Sr. Member
  • ****
  • Posts: 66
Re: Wrench Display Board
« Reply #37 on: September 23, 2018, 08:04:56 PM »
For some reason I could not send the pics on a pm so I'll try it here
 One pic shows my set which has 9 different sizes ( not 8 like I had said ) and the other picture shows the 2 that I could send you, unfortunately I don"t have a spare 5/8x9/16.The two I can send are the 1x15/16 and a 1/2x 7/16.
 It looks to me that I might be missing one size probably a 3/8x5/16.This is just a quess by looking at the lengths that get progesivly shorter as the sizes decrease
Here is a page from the ‘43 Barcalo Catalog.
-Don
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society

Online gibsontool

  • Contributor
  • Hero Member
  • ***
  • Posts: 1125
Re: Wrench Display Board
« Reply #38 on: September 24, 2018, 09:33:16 AM »
Thanks Don. Iv'e been looking for that info without any luck for a long time. Unfortunately the sizes are not very clear, The one I'm not sure of is the second to last ,the 26-731C. Could you possibly have a look and let me know what the sizes are. If you or anyone wants to do some trading of this pattern I have several duplicates. I know now that I'm missing the 26-725  7/16" x1/2" and the 26-731C whatever size that may be. Jim.

Offline turnnut

  • Hero Member
  • *****
  • Posts: 1861
Re: Wrench Display Board
« Reply #39 on: September 24, 2018, 06:35:35 PM »
 26-732C looks like 3/4"  -11/16"

Offline p_toad

  • Hero Member
  • *****
  • Posts: 527
Re: Wrench Display Board
« Reply #40 on: September 24, 2018, 07:56:12 PM »
my best reading of that is

26-731C looks like 3/4" - 15/16"

Online gibsontool

  • Contributor
  • Hero Member
  • ***
  • Posts: 1125
Re: Wrench Display Board
« Reply #41 on: September 25, 2018, 11:14:04 AM »
My first thought was 3/4 x 15/16 but that just dosn't make sense to my way of thinking. 3/4 x 11/16 sounds more logical

Offline d42jeep

  • Sr. Member
  • ****
  • Posts: 66
Re: Wrench Display Board
« Reply #42 on: September 28, 2018, 03:30:23 AM »
As illogical as it seems, I believe that size is 3/4” x 15/16”. The second half of the part number is supposed to correspond to the Industry Standard Number, as far as I can tell, and I don’t see a 731C in Alloy Artifact’s chart. I have some Double Grip DOE wrenches but I’m not sure of the sizes and I’m not where they are at the moment.
-Don
« Last Edit: September 28, 2018, 03:58:00 AM by d42jeep »
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society

Offline d42jeep

  • Sr. Member
  • ****
  • Posts: 66
Re: Wrench Display Board
« Reply #43 on: September 28, 2018, 03:59:54 AM »
Just to muddy the waters a bit more, here is a listing from 1941 that shows some different sizes.
-Don
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society

Online gibsontool

  • Contributor
  • Hero Member
  • ***
  • Posts: 1125
Re: Wrench Display Board
« Reply #44 on: September 28, 2018, 07:19:21 AM »
Like you say it's getting a little muddy. I'm going to have another look at my wrenches, I think I have some of the same sizes but the script is on the the opposite face of the wrench,maybe from different production years or whatever?????? Thanks again for the info. where the heck did you find those? Jim.