Author Topic: Wanted - Plomb 4742 and 4746 1/4” bits  (Read 3971 times)

0 Members and 1 Guest are viewing this topic.

Offline d42jeep

  • Hero Member
  • *****
  • Posts: 433
Wanted - Plomb 4742 and 4746 1/4” bits
« on: September 12, 2018, 09:47:19 AM »
Wanted - Snap-on TM-2 marked E or G to complete my Snap-on wartime 1/4” drive set.(FOUND)
-Don
« Last Edit: December 10, 2020, 03:16:30 AM by d42jeep »
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society
CONTRIBUTOR

Offline Northwoods

  • Hero Member
  • *****
  • Posts: 1901
Re: Wanted - Snap-on TM-2 from 1944 or 45
« Reply #1 on: September 12, 2018, 03:12:32 PM »
Wanted - Snap-on TM-2 marked E or G to complete my Snap-on wartime 1/4” drive set.
-Don

Best I have is a Midget M-70M date code G. Would that help?
The ORIGINAL Northwoods.

Offline d42jeep

  • Hero Member
  • *****
  • Posts: 433
Re: Wanted - Snap-on TM-2 from 1944 or 45
« Reply #2 on: September 12, 2018, 07:58:38 PM »
Thanks for the generous offer but I’m not sure what that tool is. I believe if the Snap-on number starts with an M it indicates that the tool is 9/32” drive. The ratchet in my 9/32” drive Midget set is an M-70L. Since I’m in the tool wanted section, I should mention that I’m looking for an M-21 9/32” drive screwdriver bit, if anyone has an extra. Here is the almost complete 9/32” drive set.
-Don
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society
CONTRIBUTOR

Offline Northwoods

  • Hero Member
  • *****
  • Posts: 1901
Re: Wanted - Snap-on TM-2 from 1944 or 45
« Reply #3 on: September 12, 2018, 11:13:19 PM »
Oops.  You're right.  Mine is a 9/32".
Backs slowly out of the room....
The ORIGINAL Northwoods.

Offline d42jeep

  • Hero Member
  • *****
  • Posts: 433
Found!
-Don
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society
CONTRIBUTOR

Offline EVILDR235

  • Hero Member
  • *****
  • Posts: 1323
I have a Snap-On speed wrench in 9/32 drive, but I don't think it will fit in that box. It is model M44 and has a cadmium finish. I also have two adapters to adapt from 9/32 drive down to 1/4 drive.

EvilDr235
« Last Edit: January 04, 2020, 04:59:13 PM by EVILDR235 »

Offline d42jeep

  • Hero Member
  • *****
  • Posts: 433
Re: Wanted - Plomb 4742 and 4746 to complete my 4700R 1/4” drive set
« Reply #6 on: December 10, 2020, 03:07:44 AM »
I need a Plomb 4742 and 4746 to complete a set. 1/7/2022. I found the 4746 now am only missing the 4742.
-Don
« Last Edit: January 07, 2022, 05:35:45 PM by d42jeep »
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society
CONTRIBUTOR

Offline d42jeep

  • Hero Member
  • *****
  • Posts: 433
Re: Wanted - Plomb 4742 and 4746 1/4” bits
« Reply #7 on: January 07, 2022, 05:37:44 PM »
This is a picture of the Plomb 4742 that I’m missing.
-Don
Member of PHARTS-  Perfect Handle Admiration, Restoration and Torturing Society
CONTRIBUTOR