« previous next »
Pages: [1]   Go Down

Author Topic: patented  (Read 3476 times)

0 Members and 1 Guest are viewing this topic.

Offline jimwrench

  • Contributor
  • Hero Member
  • ***
  • Posts: 1803
patented
« on: July 14, 2014, 04:01:15 PM »
 Patented by whom for what ?
 right and left hand thread.
 washer like piece in end of nut has 5/16 thread that is only about three threads deep.
 PM and patd are only markings.
Logged
Jim
Mr. Dollarwrench

Offline EVILDR235

  • Hero Member
  • *****
  • Posts: 1323
Re: patented
« Reply #1 on: July 14, 2014, 05:05:25 PM »
That is a spring shackle for a old car or truck back then you greased them. They were replaced by rubber mounted spring shackles.



EvilDr235
« Last Edit: July 14, 2014, 07:00:19 PM by EVILDR235 »
Logged

Offline rusty

  • Hero Member
  • *****
  • Posts: 4345
Re: patented
« Reply #2 on: July 16, 2014, 03:43:47 PM »
Why would it need left hand threads?
Logged
Just a weathered light rust/WD40 mix patina.

Offline jimwrench

  • Contributor
  • Hero Member
  • ***
  • Posts: 1803
Re: patented
« Reply #3 on: July 16, 2014, 04:16:15 PM »
 Don't know.  its not like any spring shackle I've seen. If you put grease in the end it would grease the threads but not the leafs. I'm guessing automotive but not convinced on automotive what.
Logged
Jim
Mr. Dollarwrench

Offline EVILDR235

  • Hero Member
  • *****
  • Posts: 1323
Re: patented
« Reply #4 on: July 16, 2014, 06:14:58 PM »
Go to a search engine and type in Dodge spring shakles 1940s and you will see several pictures of them. I was in the auto wrecking trade for over 35 years and removed and replaced many of them.

Evildr235
Logged

Offline wrenchguy

  • Hero Member
  • *****
  • Posts: 480
  • I like odd old stuff, especially mechanical.
    • Wrenchguys videos
Re: patented
« Reply #5 on: July 16, 2014, 07:16:45 PM »
its not flat where it would come in contact with the spring........  fits into a saddle then the spring????????
Logged

Offline jimwrench

  • Contributor
  • Hero Member
  • ***
  • Posts: 1803
Re: patented
« Reply #6 on: July 16, 2014, 08:45:08 PM »
 I went I saw I am convinced. Now what do I do with one of them. take it to auction and see if anyone is working on 1940's Dodge.
Logged
Jim
Mr. Dollarwrench

Offline EVILDR235

  • Hero Member
  • *****
  • Posts: 1323
Re: patented
« Reply #7 on: July 16, 2014, 09:02:00 PM »
That is  a shakle,not a u-bolt. One side goes in the bracket on the frame and the other in eye hole of the spring. Several different car makers used this system. Not the best setup.

XXXXXX
« Last Edit: July 16, 2014, 09:04:36 PM by EVILDR235 »
Logged

Offline Chillylulu

  • CONTRIBUTOR
  • Hero Member
  • *****
  • Posts: 1533
Re: patented
« Reply #8 on: July 17, 2014, 01:51:18 AM »
Shackle on top, u-bolt on rear driveshaft. See the beautiful old Buick below:





I hope this helps to clear up the difference. 


Chilly
Logged

Offline eddie hudson

  • Hero Member
  • *****
  • Posts: 3619
  • NYC
Re: patented
« Reply #9 on: July 17, 2014, 06:02:26 AM »
Quote from: rusty on July 16, 2014, 03:43:47 PM
Why would it need left hand threads?


It has something to do with keeping the whole thing tight. One side of the car had right handed thread on both upper and lower while the other had left and right.
Logged

Offline Billman49

  • Hero Member
  • *****
  • Posts: 790
  • Collector of edged tools, especially billhooks...
    • A Load of Old Billhooks
Re: patented
« Reply #10 on: July 17, 2014, 11:30:26 AM »
Never seen an open ended version in the UK - they are usually found with a plate either side of the spring and hanger....



as per this repair kit for a 4x4, and this from the same web page...
« Last Edit: July 17, 2014, 11:35:26 AM by Billman49 »
Logged
Pages: [1]   Go Up
« previous next »