« previous next »
Pages: [1]   Go Down

Author Topic: BT-50 Gage for 51 Points  (Read 3711 times)

0 Members and 1 Guest are viewing this topic.

Offline OilyRascal

  • Contributor
  • Hero Member
  • *****
  • Posts: 2282
    • Facebook Profile
BT-50 Gage for 51 Points
« on: January 11, 2013, 07:11:32 PM »
I have this tool I'm seeking information on.  It is marked "BT-50 GAGE FOR 51 POINTS" with "221" and "059" also stamped.  It measures 4" long.  It was found among "Carter" carb. tools, but is not marked with a maker.  Any information is appreciated.



Logged
"FORGED IN THE USA" myself.  Be good to your tools!

Garden and Yard Rustfinder Extraordinaire!
http://www.papawswrench.com/vboard/index.php?topic=3717

Offline john k

  • Contributor
  • Hero Member
  • ***
  • Posts: 2657
Re: BT-50 Gage for 51 Points
« Reply #1 on: January 11, 2013, 07:15:11 PM »
The marking 51 points to me indicates it is for setting ignition points in the distributor.  The wire is what diameter ?    Looking at it closer it says for '51 Pontiac Six.   
« Last Edit: January 11, 2013, 07:17:50 PM by john k »
Logged
Member of PHARTS - Perfect Handle Admiration, Restoration and Torturing Society

Offline lauver

  • Hero Member
  • *****
  • Posts: 690
  • Belton, TX
Re: BT-50 Gage for 51 Points
« Reply #2 on: January 11, 2013, 07:24:38 PM »
Quote from: john k on January 11, 2013, 07:15:11 PM
The marking 51 points to me indicates it is for setting ignition points in the distributor.  The wire is what diameter ?    Looking at it closer it says for '51 Pontiac Six.

+1
Logged
Member of PHARTS - Pefect Handle Admiration, Restoration, and Torturing Society

Offline Papaw

  • Owner/Administrator
  • Moderator
  • Hero Member
  • *****
  • Posts: 11221
  • Alvin, Texas
    • Papawswrench
Re: BT-50 Gage for 51 Points
« Reply #3 on: January 11, 2013, 07:27:49 PM »
Yep, it says 51 PONT- Pontiac

If it is a carb tool, which Carter suggests, it might be for float setting or such.
Logged
Member of PHARTS - Perfect Handle Admiration, Restoration and Torturing Society
 
 Flickr page- https://www.flickr.com/photos/nhankamer/

Offline krusty the clown

  • Sr. Member
  • ****
  • Posts: 154
Re: BT-50 Gage for 51 Points
« Reply #4 on: January 11, 2013, 07:48:42 PM »
Choke unloader guage?  I used to use drll bits.
Logged

Offline Papaw

  • Owner/Administrator
  • Moderator
  • Hero Member
  • *****
  • Posts: 11221
  • Alvin, Texas
    • Papawswrench
Re: BT-50 Gage for 51 Points
« Reply #5 on: January 11, 2013, 08:34:45 PM »
Quote
Choke unloader guage
<---- Yes. I just couldn't think of it before- been many years.
Logged
Member of PHARTS - Perfect Handle Admiration, Restoration and Torturing Society
 
 Flickr page- https://www.flickr.com/photos/nhankamer/

Offline OilyRascal

  • Contributor
  • Hero Member
  • *****
  • Posts: 2282
    • Facebook Profile
Re: BT-50 Gage for 51 Points
« Reply #6 on: January 12, 2013, 05:18:26 AM »
Many thanks for the assistance!

Is there a simple explanation for what it means to "Unload" a choke?
Logged
"FORGED IN THE USA" myself.  Be good to your tools!

Garden and Yard Rustfinder Extraordinaire!
http://www.papawswrench.com/vboard/index.php?topic=3717

Offline krusty the clown

  • Sr. Member
  • ****
  • Posts: 154
Re: BT-50 Gage for 51 Points
« Reply #7 on: January 12, 2013, 05:45:04 AM »
Quote from: OilyRascal on January 12, 2013, 05:18:26 AM
Many thanks for the assistance!

Is there a simple explanation for what it means to "Unload" a choke?
it's how far the choke plate opens when the vacuum pull-off pulls it open when the engine starts cold (other wise it would stall). Also the choke is mechanicly opened at WOT to clear floods. Both must be adjusted to a spec. Before we stopped using carbs the specs were changed  to degrees of open but before that it was measure in thousands of an inch between the choke plate and the housing.
Logged

Offline krusty the clown

  • Sr. Member
  • ****
  • Posts: 154
Re: BT-50 Gage for 51 Points
« Reply #8 on: January 12, 2013, 05:51:22 AM »
I forgot to mention that the BT prefix indicates that its a burroughs tool. Burroughs made GM Special tools as well as parts dept shelving and service writers desks. They are still in business.but no longer making tools.
Logged

Offline Ken W.

  • CONTRIBUTOR
  • Contributor
  • Hero Member
  • ***
  • Posts: 691
Re: BT-50 Gage for 51 Points
« Reply #9 on: January 12, 2013, 11:08:14 AM »
That looks very similar to the Tecumseh carb tool for setting the float and replacing the seat.
Logged

Offline Lostmind

  • Hero Member
  • *****
  • Posts: 1567
  • Wellington, Ohio 44090
Re: BT-50 Gage for 51 Points
« Reply #10 on: January 12, 2013, 11:41:30 AM »
How about  .221 and .059   being the sizes?
Logged
Of all the things I've lost , I miss my mind the most

Offline amertrac

  • Contributor
  • Hero Member
  • *****
  • Posts: 1880
  • ny mountain man
Re: BT-50 Gage for 51 Points
« Reply #11 on: January 12, 2013, 12:10:45 PM »
I worked for pontiac 1952 t0 1963  and used that tool many times and you got the right answer here    bob w.
Logged
TO SOON ULD UND TO LATE SCHMART

Offline OilyRascal

  • Contributor
  • Hero Member
  • *****
  • Posts: 2282
    • Facebook Profile
Re: BT-50 Gage for 51 Points
« Reply #12 on: January 12, 2013, 01:51:04 PM »
Thanks again!  Appreciate all the information.
Logged
"FORGED IN THE USA" myself.  Be good to your tools!

Garden and Yard Rustfinder Extraordinaire!
http://www.papawswrench.com/vboard/index.php?topic=3717
Pages: [1]   Go Up
« previous next »