News:

"A determined soul will do more with a rusty monkey wrench than a loafer will accomplish with all the tools in a machine shop." - Robert Hughes

Main Menu

Need help with a drill.

Started by m_fumich, April 28, 2012, 01:35:24 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

m_fumich

I'm gonna restore this drill if I can. Any idea how the chuck comes off? It's a Jasco Junior.



JessEm

Quote from: m_fumich on April 28, 2012, 01:35:24 PM
Any idea how the chuck comes off?

Milwaukee Porta-Band?




Seriously though, I have no idea. Wish I could be more help. Good luck with it.
Vintage Power Tools WANTED: Porter Cable 500 belt sander, beam saws (circular saws with 10"+ blades) including Mall Saw 120, Skil 127, Makita 5402A & 8190039, B&D, ETC...

rusty


There is usually a screw inside the jaw (which means you have to get the jaw to open first. Good luck -P

*beware* - sometimes the screw has left hand threads.
Just a weathered light rust/WD40 mix patina.

Papaw

Quote*beware* - sometimes the screw has left hand threads.
And often quite tight due to the rotation and years of not being removed!
Member of PHARTS - Perfect Handle Admiration, Restoration and Torturing Society
 
Flickr page- https://www.flickr.com/photos/nhankamer/

dimwittedmoose51

I'd say the first step is a week's worth of an ATF/Acetone bath and the nsee if the chuck will spit  that bit out.  Let us know how that goes.....

DM&FS

Champion Pawn/Flea Plunderer
Old Tools and Music.....My drugs of choice

scottg

#5
If the drill has reverse, it will definitely have a screw inside the chuck and it will definitely be left handed.
It probably doesn't reverse though, from the age of it.

But you still have to open the chuck to check!!
If it has one, it has to come out first!!

  After the week long (2 is better) soak in penetrant, put a 3/8" hex key in the jaws (the short side) and cinch the jaws down tight.
Now take a light hammer and knock the chuck loose by striking the long leg of the allen key in a counterclockwise manner.   
You want lightweight hammer (8-10oz) and a very fast, hard blow.
or 50 blows.
But it will eventually relent, and its the only way without damaging a whole lot of stuff.

Bigger hammer is no good. Impact wrench, definitely no good!
fast hard impact from a light hammer will work, eventually
yours Scott 
PHounding PHather of PHARTS
http://www.snowcrest.net/kitty/sgrandstaff/

Fins/413

Good luck Matt that is a good looking drill.
1959 Chrysler New Yorker
1982 E150 Ford van

m_fumich

#7
It does not have reverse. The motor still works but I don't use it. I put that bit in several years ago. I let it sit under the car port until s couple yours ago. The last time I used it was the first time I used it. It made my hand all tingly.

It will get at least 2 weeks on JAFE Juice. I'm out 2 weeks at a time, at least. Once I set it up to soak, no one will touch it until I get home. I just need to find some place to put it. No garage or car port at this house.

Papaw

Quotecat port
Matt, most cats don't need a special place to lay around!
Member of PHARTS - Perfect Handle Admiration, Restoration and Torturing Society
 
Flickr page- https://www.flickr.com/photos/nhankamer/

m_fumich

THAT'S what you pick up on. No comment about the drill making me feel like I had a couple bumble bees in my hand? Sure, go straight for the funny stuff. :)

Papaw

The tingling was in anticipation of my jibe at you about a "Cat Port"!
Member of PHARTS - Perfect Handle Admiration, Restoration and Torturing Society
 
Flickr page- https://www.flickr.com/photos/nhankamer/

Branson

Quote from: Papaw on April 29, 2012, 06:06:13 PM
[Matt, most cats don't need a special place to lay around!

Sure they do!  On top of anything, especially anything you just laid down.  It's all special to cats.