'The Masterpiece" Wrench

[Lostmind]

I bought this just to share with you guys.The jaw has a pipe cutter ,and it flips over to use as a pipe wrench.It's a hammer and nail puller also.
I never saw one , but it's probably pretty common to you guys.
The rust was worst at the name , and it seems the more I did ,the harder it got to read.
Could be Bonney vise &tool co. or donney vise & tool Co.?Phil. Pa.
Says "The Masterpiece" Established 1876.
I tried to google it , but not sure of the name.
Also got the Vise at same place, don't know if it's same period?
Let me know your thoughrs
Thanks Roy

[johnsironsanctuary]

Roy, That is a Bemis & Call Combination wrench. I have never seen one with the pipe jaw that you have. Your is called a long nut. What is probably stamped in it is Bemis & Call H and T co.  'Hardware and Tool' Excuse me for drooling a little, but would you care to part with it? PM me.

[rusty]

It is The Masterpiece, and it is by Bonney Tool & Vise Works,Phila,PA.
It is shown in 1906 Hardware Dealers Magazine. Adv claim patents of
Mar 3, 1903 ; Aug 9, 1904

Very nice :)

Mar patent: http://www.datamp.org/patents/displayPatent.php?number=721660&typeCode=0
Aug patent: http://www.datamp.org/patents/displayPatent.php?number=767,199&type=

[Plyerman]

Sweet! That's really a special one there.

You ought to think about spinning up a new wooden grip for it Lostmind.

[johnsironsanctuary]

OOPS! I assume that it was a way to get around the Bemis and Call patents.  Thanks Rusty.








So Dumb So Soon, So Smart So late!

[rusty]

It is the classic Bemis & Call pattern, but the patents on the basic B&C dogged jaw were  25+ years old and long expired...

[Lostmind]

Fast work Rusty.I'm going to try Bing , haven't had much luck with google.
It seems like they always direct me somewhere to buy something.
I have seen quite a few Bemis and Call S Wrenches , but none of the interchangable jaw wrenches.

[Lostmind]

Well , I went back to Google and there is a lot of info.I originaly thought it was Bonley,
and didn't go back to Bonney.Thanks again ,
Roy

[Branson]

That * Ford carb , hubcap wrench looks more like a small saw vise to me.

[Lostmind]

Yes it is , that's my file ID , it's in with some items I have for sale.
I know there is supposed to be a way to hide it, but I'm still learnig
this computer stuff.
The vise came from the same stash as the wrench.
It's cast iron , with a number three cast in it. Can't find any other markings.
I thought it was a small saw vise?
Works good , I'll probably keep it on the workbench as a third hand.

[rusty]

I like the saw vise, it's a nice simple, clean design.
Don't squeeze too hard with it, it's likely cast iron...

[Lostmind]

Here is The " Masterpiece " with a "borrowed" Handle from a Stilson pipe wrench and a photo of the "new" handle to go on the Stilson.

[scottg]

Not a saw vise.
  People always think they are but they are wrong. 
If you tried to mount a saw in it, you'll find its not deep enough and the saw sticks up above the jaws 2 or 3 inches! Its nowhere near heavy enough either.
Filing a spring steel saw blade with a file, that is held in very thick cast iron vise jaws? Right up close only 1/8" below the file?  Is already hard enough on files. They don't last long at best.
Trying to file one free hanging in space by 3"? 
The file wouldn't last 4 strokes!   Screeeeeeeech!

On the other hand, .....say your wallet blows out a seam?
Or your keychain/coin purse loses its stitching?
  Your harness needs repair????    Again???? Already??

Try a lacing pony!!!
  Holds the leather just perfect. You can stitch right above the jaws and it doesn't squirm around on you at all! You can even stitch "both ways" with a needle in each hand, just like a pro!
  yours Scott

[rusty]

>a lacing pony...

Ahh!

[Lostmind]

Always a daily lesson here at Tool Talk,
Thanks