« previous next »
Pages: [1]   Go Down

Author Topic: Barcalo question  (Read 2061 times)

0 Members and 1 Guest are viewing this topic.

Offline Lostmind

  • Hero Member
  • *****
  • Posts: 1567
  • Wellington, Ohio 44090
Barcalo question
« on: October 15, 2012, 12:10:16 PM »
Did this style come in a set?
This is the only size I've ever found. Special application?
Logged
Of all the things I've lost , I miss my mind the most

Offline lauver

  • Hero Member
  • *****
  • Posts: 690
  • Belton, TX
Re: Barcalo question
« Reply #1 on: October 15, 2012, 12:45:51 PM »
Lost,

Yes, it came in a set (auto kit wrenches).  They're nice wrenches, unusual (not combo wrenches... they're open/box end wrenches with a different size on both ends) and they are usually fairly priced.  YMMV
Logged
Member of PHARTS - Pefect Handle Admiration, Restoration, and Torturing Society

Offline Lewill2

  • Hero Member
  • *****
  • Posts: 2004
  • Bucks County PA
Re: Barcalo question
« Reply #2 on: October 15, 2012, 01:25:51 PM »
I don't think that one was part of a standard set. Didn't they have a tapered pin that held the set together and a knurled nut on the pin? Some of them had a wing nut that held the set together also. This one doesn't have a hole for the pin, unless some of the came with a wire clip that held the set together.
Logged

Offline keykeeper

  • Hero Member
  • *****
  • Posts: 1053
Re: Barcalo question
« Reply #3 on: October 15, 2012, 02:58:42 PM »
I have wrenches like this with the hole and without the hole.

I think a lot of it depends on manufacturer.
Logged
-Aaron C.

My vintage tool Want list:
Wards Master Quality 1/2" drive sockets (Need size 5/8), long extension, & speeder handle.
-Vlchek WB* series double box wrenches.
-Hinsdale double-box end round shank wrenches.

Offline Lostmind

  • Hero Member
  • *****
  • Posts: 1567
  • Wellington, Ohio 44090
Re: Barcalo question
« Reply #4 on: October 15, 2012, 03:30:53 PM »
I have this stamped steel set that has the different sizes and the hole
it's odd that I've only seen that 5/8 X 3/4 Barcalo in that style and size
Roy
Logged
Of all the things I've lost , I miss my mind the most

Offline keykeeper

  • Hero Member
  • *****
  • Posts: 1053
Re: Barcalo question
« Reply #5 on: October 16, 2012, 09:17:32 AM »
Here's a 7/16 x 3/8 by Barcalo, with the hole.

I'll have to dig out the others I have later on.

Logged
-Aaron C.

My vintage tool Want list:
Wards Master Quality 1/2" drive sockets (Need size 5/8), long extension, & speeder handle.
-Vlchek WB* series double box wrenches.
-Hinsdale double-box end round shank wrenches.

Offline Lostmind

  • Hero Member
  • *****
  • Posts: 1567
  • Wellington, Ohio 44090
Re: Barcalo question
« Reply #6 on: October 16, 2012, 09:56:51 AM »
sure looks like the same wrench ,with a hole drilled in it.Thanks
Logged
Of all the things I've lost , I miss my mind the most
Pages: [1]   Go Up
« previous next »