« previous next »
Pages: [1]   Go Down

Author Topic: K.R. Wilson  (Read 3277 times)

0 Members and 1 Guest are viewing this topic.

Offline HeelSpur

  • Hero Member
  • *****
  • Posts: 2033
  • Contributor
K.R. Wilson
« on: September 22, 2013, 05:18:26 PM »
Anyone familiar with these tools? Found this one today but come up empty on it, but found this site that is pretty cool but still no info. There is a forum but it doesn't seem very busy.
http://krwilsontools.com/






Logged
RooK E

Offline rusty

  • Hero Member
  • *****
  • Posts: 4345
Re: K.R. Wilson
« Reply #1 on: September 22, 2013, 05:55:20 PM »
Mentioned as 1939-1942 Ford Brake Adjusting Tool, dunno how reliable that is tho.
I think tha XA numbers were a transition numbering system before the modern ford part numbering system.....

Logged
Just a weathered light rust/WD40 mix patina.

Online skipskip

  • Contributor
  • Hero Member
  • *****
  • Posts: 1518
  • Glenmont NY USA
Re: K.R. Wilson
« Reply #2 on: September 22, 2013, 06:42:41 PM »
looks little like model A flywheel wrench, what size openings?
Logged
A place for everything and everything on the floor

Online skipskip

  • Contributor
  • Hero Member
  • *****
  • Posts: 1518
  • Glenmont NY USA
Re: K.R. Wilson
« Reply #3 on: September 22, 2013, 06:51:58 PM »
you're not kidding about the wilson forum, it's  a ghost town
Logged
A place for everything and everything on the floor

Offline HeelSpur

  • Hero Member
  • *****
  • Posts: 2033
  • Contributor
Re: K.R. Wilson
« Reply #4 on: September 22, 2013, 07:07:31 PM »
Didn't measure the openings and its not marked.
Will in the morning.
Logged
RooK E

Offline Ken W.

  • CONTRIBUTOR
  • Contributor
  • Hero Member
  • ***
  • Posts: 691
Re: K.R. Wilson
« Reply #5 on: September 22, 2013, 07:43:19 PM »
Not too long ago there was a H press on CL made my Wilson. The factory was in Arcade,New York about 45 minutes SE of Buffalo.They made a lot of stuff.
Logged

Offline mvwcnews

  • Hero Member
  • *****
  • Posts: 962
Re: K.R. Wilson
« Reply #6 on: September 23, 2013, 07:56:51 AM »
"K.R. Wilson Buffalo, N.Y. Exclusive Builder of Approved Ford Shop Equipment since 1916" -- from a 1937 Popular Science ad.
Anyone in the forum close to the Detroit Public Library to hunt up a FORD shop manual to find the application for this one?
Logged

Offline HeelSpur

  • Hero Member
  • *****
  • Posts: 2033
  • Contributor
Re: K.R. Wilson
« Reply #7 on: September 23, 2013, 04:44:03 PM »
Quote from: skipskip on September 22, 2013, 06:42:41 PM
looks little like model A flywheel wrench, what size openings?
Believe they are 1" & 13/16".
Logged
RooK E

Offline crankshaftdan II

  • Hero Member
  • *****
  • Posts: 285
Re: K.R. Wilson
« Reply #8 on: October 03, 2013, 02:10:53 PM »
Quote from: HeelSpur on September 22, 2013, 05:18:26 PM
Anyone familiar with these tools? Found this one today but come up empty on it, but found this site that is pretty cool but still no info. There is a forum but it doesn't seem very busy.
http://krwilsontools.com/







Put er up on Flea Bay--if it has value some collector will snag it!
Logged
E-mail address  dhdslimbow@yahoo.com
Looking for USA made ratchets-all sizes-drives and lengths  also S-K SuperKrome wrenches ditto.  Like to trade vs buy run it past me-nothing is cut in stone!

Offline Lostmind

  • Hero Member
  • *****
  • Posts: 1567
  • Wellington, Ohio 44090
Re: K.R. Wilson
« Reply #9 on: October 03, 2013, 03:46:47 PM »
The brake adjusting wrenches are 8 point, for the square head adjuster. I think they are 7/16 and 1/2"
Logged
Of all the things I've lost , I miss my mind the most
Pages: [1]   Go Up
« previous next »